Skip to content
Call us for a Free Quote: (416) 966-4200 Free Quote

Can You Stain Interlocking Brick?

November 10, 2026
epoxy garage floor

Ask a Question

Send us a note and we'll get back to you — usually within one business day.

What’s it about?

Where you are, rough size, and what state it’s in — that’s usually enough to answer without coming out.

We’ll only use your details to answer this — no lists, no marketing.

Yes, interlocking brick can often be stained to change its colour, but staining is not the same as sealing. Staining recolours the surface of the pavers, while sealing protects them from water, stains and wear. The two treatments suit different goals, and not every paver takes stain well, so the honest answer for many GTA driveways is that it depends on the stone.

Staining versus sealing: what each one does

Staining applies colour to the paver surface to change its shade or deepen its tone. Concrete pavers tend to absorb stain more readily than clay brick, and the result can revive faded colour or create a different look. What staining does not do is protect the surface. It sits on the face of the stone, where traffic, weather and road salt can still take their toll.

Sealing is a different job. A sealer bonds to the pavers so water, oil and grime sit on top instead of soaking in, and it helps lock the joint sand between the stones. Sealing does not change colour the way staining does, although some sealers can deepen the tone slightly.

The short version: stain for colour, seal for protection. On driveways and walkways that face salt, freeze-thaw cycles and summer sun, protection usually matters more than a colour change.

Which interlock surfaces can be stained

Not every paver is a good candidate. Bare, clean concrete pavers are usually the most predictable, because the surface is absorbent enough to take colour evenly. Results get less certain when the stone has been treated, aged or damaged. Situations where staining tends to be less predictable include:

  • Pavers that already carry a sealer or glossy coating, which blocks the stain from absorbing
  • Surfaces with efflorescence, the white powdery bloom that sometimes appears on concrete
  • Pavers with cracks, chips or loose joints, where colour can settle unevenly
  • Areas with poor drainage, where standing water keeps the surface damp

Clay brick behaves differently from concrete paver, and older or heavily worn surfaces can take colour unevenly no matter how careful the preparation. If you are not sure whether staining will suit your particular pavers, ask us whether it suits your surface — the answer depends on the stone, its age and its condition.

How GTA weather affects stained interlock

Whatever is applied to interlock in the Greater Toronto Area has to survive a full year of stress. Freeze-thaw cycles are the biggest test: when water works into the joints and freezes, it expands and presses against the stones, which can loosen them over many winters. Road salt adds a second problem, because it attracts moisture and leaves a white, crusty residue that dulls the surface.

Spring rain falls at the worst time on clay-heavy soil, which drains slowly, so driveways and walkways can stay damp for longer than homeowners expect. Summer brings strong UV light that fades colour over time — and staining alone does not stop that fading.

None of this means staining cannot work in the GTA. It means the surface underneath matters as much as the stain. Sound joints, proper drainage and clean, dry pavers give any treatment its best chance of lasting.

What a careful staining job involves

A worthwhile result starts well before any colour goes on. The pavers need to be cleaned so that dirt, moss, old sealer and efflorescence are removed rather than sealed under the stain. The surface then needs to dry fully, because colour applied to damp stone can look patchy.

From there, a careful job usually includes:

  • Testing the stain on a small, low-visibility area to confirm the colour takes evenly
  • Applying the stain in consistent passes so the finish does not look streaky
  • Keeping foot and vehicle traffic off the surface until it has cured

With interlock, the joints matter too. If joint sand has washed out, the whole surface looks tired no matter what colour the pavers are, so re-sanding is often part of the preparation. Staining is not right for every stone, so ask us whether it suits your surface before you commit.

Staining or sealing: choosing what your surface needs

The choice comes down to what you want to change. If the goal is a different or deeper colour, staining is the topic to explore. If the goal is to protect the pavers from water, salt, stains, fading and washed-out joints, sealing is usually the better fit — and it is the service Seal Tech provides for interlock driveways, walkways and patios.

Sealing also works hand in hand with cleaning and re-sanding. Clean the surface, top up the joint sand, then seal, and the result is protected rather than simply recoloured. Our interlock driveway, walkway and patio cleaning, re-sanding and sealing service treats the job as one process. If you are weighing staining against sealing, read our guide to interlocking brick sealing for a fuller picture.

Frequently Asked Questions

Will staining protect interlock from road salt and freeze-thaw?

Not the way a sealer does. Staining changes colour; it does not lock joint sand or repel water the way sealing does, so protection is not the main reason to stain.

Can I stain pavers that are already sealed?

Usually not without extra work. A sealer blocks absorption, so the stain can sit on top and look uneven. The old sealer would need to be removed first, and even then the result depends on the stone.

Will stained interlock fade in summer sun?

Colour can fade over time under strong UV, especially if nothing is applied over the stain to protect it. GTA summers put real UV stress on driveways and patios.

Should I stain or seal my interlock driveway?

It depends on your goal. Want a different colour? Staining is the option to research. Want protection from water, salt and wear? Sealing is usually the better fit. Ask us whether it suits your surface.

Seal Tech Inc. serves Scarborough and the GTA. Call (416) 966-4200 for a free written quote, or contact us to send photos with your quote request.

HomeStars Best of 2023, 2024, 2025

We were named Best Concrete Contractor 3 years in a row by HomeStars

Get a free quote

Serving Scarborough and the Greater Toronto Area. Tell us what needs doing.

Or call (416) 966-4200

No obligation. We never share your details.

Thanks — your request is in. We'll be in touch shortly.

Something went wrong. Please call (416) 966-4200 instead.

Ready to make your surfaces look new again?

Free, no-obligation quotes across the GTA — usually within one business day.